![force enable trim mac os high sierra force enable trim mac os high sierra](http://hopdeut.weebly.com/uploads/1/3/3/5/133540459/175059136_orig.jpg)
- Force enable trim mac os high sierra install#
- Force enable trim mac os high sierra update#
- Force enable trim mac os high sierra full#
Because it causes that my USB 3.0 ethernet adapter doesn’t work with system restored by this way.
Force enable trim mac os high sierra install#
![force enable trim mac os high sierra force enable trim mac os high sierra](http://copperpassl.weebly.com/uploads/1/2/6/7/126759394/113983072_orig.jpg)
You can watch percentage process using this command in Terminal: sudo fsesetup status It will take VERY looooong time (cca 24 hours in my case: cca 400 GB on 1TB disk). Now you can enable FileVault if you want to encrypt the volume (System Preferences -> Security & Privacy -> FileVault).If it freezes just after restart, see above to the issues.
![force enable trim mac os high sierra force enable trim mac os high sierra](http://www.urban75.org/blog/images/comacchio-ferrera-italy-13.jpg)
After Time Machine restoration it will restart to your restored system.It will take long time (cca 3–4 hours in my case for cca 400 GB). Close the Disk Utility and run Time Machine restoration.Encryption can be enabled afterwards (by FileVault). Time Machine will recreate volume to unencrypted one :(. If you want restore to an encrypted volume, it’s useless to prepare the encrypted volume. Create new APFS volume on your new SSD.Run Disk Utility and mount it (and unlock it if it’s encrypted). Restore data from Time Machine (direct 1:1 variant) Don’t forget to enable TRIM support ( sudo trimforce enable ) after installation. If you can’t see your new SSD either, something is wrong. If you can’t see your new disk even in Disk Utility, switch view mode to “Show all devices”. If you can’t see your SSD in OS instalator, use Disk Utility to create new APFS volume on your new SSD. If you don’t want to restore your data from Time Machine, you can install OS now.You can press alt key when you hear the jingle sound to select boot medium. Insert USB stick with OS installer and boot it up.After NVRAM reset you can shut down computer. Maybe it isn’t necessary, but I have used it for sure. Press and hold keys cmd+opt(alt)+R+P, start the computer while holding them and wait for jingle sound.Turn it over and plug the power adapter back. Put and screw back the cover (don’t forget that two shorter screws are under the display). !!! Don’t forget to plug back the battery connector !!! THIS IS VERY IMPORTANT.Ĩ. Then put them together to computers connector and fix it with screw.ħ. This step is more important than it looks. Notice that there are two latches under the the middle of cover, so you can use a little bit more force to loose them. Gently pull the cover up (from the display side).Remind it for the time when you will screw it back. Notice that two of them under the display are little bit shorter than the other ones. Use pentalobe P5 to unscrew 10 screws.Flip it over upside down (you can use some pad to avoid scratches on a lid). Shutdown computer, remove power adapter and all peripherals.
Force enable trim mac os high sierra full#
optional: external hard drive with Time Machine full backup (if you want to move your data from existing SSD).
Force enable trim mac os high sierra update#
![force enable trim mac os high sierra force enable trim mac os high sierra](https://venturebeat.com/wp-content/uploads/2018/06/iPad-YouTube-Sharing.jpg)
The result: YES, it works correctly with third update of MacOS High Sierra (10.13.3). But there are some discussions and youtube videos saying that it can work. The original SSD have been connected to PCIe, but it worked in AHCI mode. I was not sure if my computer can work with NVME disk. One of them does not work (or maybe i haven’t used it correctly), next one worked, so I didn’t try other one. I have ordered all three of them… just for sure ).